JIS B1501 PDF

JIS B Rolling bearings — Balls (Foreign Standard). standard by Japanese Industrial Standard / Japanese Standards Association. Standards and specifications are regulated in accordance with JIS B The nominal manufacturing sizes of steel balls are shown in the. JIS B Rolling bearings — Balls (Foreign Standard). Available for Subscriptions. Content Provider Japanese Industrial Standards [JIS].

Author: Nijora Dousho
Country: Peru
Language: English (Spanish)
Genre: Love
Published (Last): 8 May 2007
Pages: 411
PDF File Size: 9.30 Mb
ePub File Size: 3.20 Mb
ISBN: 228-9-93418-420-6
Downloads: 31882
Price: Free* [*Free Regsitration Required]
Uploader: Akinokazahn

Our trained engineers also work closely with our customers to develop products most suitable for their applications. The difference between the mean diameter of a ball lot and the sum of the nominal ball diameter and the ball gauge. The designations which is used for the purpose of general identification of a steel ball by dimension.

The principal terms, quantitative symbols and definitions used in this Standard shall be as follows. Diameter Tolerance The maximum allowable deviation of any ball mean diameter from the nominal ball diameter. This Japanese Industrial Standard specifies requirements jix finished steel balls for rolling bearings. The ball diameter variation, sphericity and surface roughness of the steel balls shall comply with Attached Table 2.

Mean Diameter of a Ball The arithmetical mean of the largest and the smallest single diameter of the ball.

Measured by two parallel plane tangent to the surface of the ball. This term is applicable to case hardened ball only.

JIS B – Rolling bearings — Balls (Foreign Standard)

Ball grade is indentified by the letter G and a number. Sphericity The greatest radial distance in any radial plane between a sphere circumscribed around the ball surface and any point on the ball surface. The hardness of steel balls larger than 3mm shall be measured in accordance with JIS Z Grade A specific combination of dimensional form and surface roughness tolerance Nomintal ball Diameter The diameter value that is used for the purpose of general identification of a ball size.

  KYUSHO-JITSU THE DILLMAN METHOD OF PRESSURE POINT FIGHTING PDF

A definite quantity of balls manufactured under conditions presumed uniform and which is considered as an entity. The mean diameter of a ball shall be obtained in the form of the arithmetic mean of the largest and smallest actual single diameters, and the ball diameter variation shall be obtained in the form of the difference between the largest and smallest actual single diameters.

The arithmetical mean of the mean diameters of the largest ball and the smallest ball in a ball lot.

And it is conventionally defined within the area where deviation of form are eliminated. Lot Mean Diameter The arithmetical mean of the mean diameter of the largest ball and that of the smallest balls in the lot. The radial distance between the smallest circumscribed sphere and the greatest inscribed v1501, with their centers common to the least squares sphere centre.

The difference between the mean diameters of the largest ball and the smallest ball in a ball lot. The diameter necessary for determining the mean diameter of a ball and the ball diameter variation shall be jie with the ball placed between the horizontal plane and the stylus applied vertical to it from different directions.

The mean diameter of a ball shall be corrected taking into account the elastic approach value due to the measuring force and also, as s rule, the elastic approach value due to the mass of the steel ball. Waviness components on the surface of a ball are usually measured with a waviness-meter using a filter.

  APPLIED LOGISTIC REGRESSION DAVID HOSMER AND STANLEY LEMESHOW PDF

Precision Hardened Balls – Metric / Inch

The amount by which the mean diameter of ball lot should differ from the nominal ball diameter, this amount being one of an established series. A specific combination of dimensions, form, surface roughness and sorting tolerances. Hardness The measure of resistance to penetration h1501 the ball surface or truncated flat of the ball by a specific indenting shape.

The various types of deviation from the perfect spherical ball surface, uniformly or non-uniformly distributed and repeated around the ball surface. Lot Diameter Variation The difference between the mean diameter of the largest ball and that of the smallest ball jix the lot.

The method of evaluating the deviation from spherical form of a steel ball shall be b1510 accordance with JIS B appendix A. Lot is the definite quantity of ball manufactured under uniformed condition.

Case Depth The distance measured radially from the surface of the ball to the point where the ball hardness becomes Rc Surface Roughness Surface roughness consists of all those irregularities such as crack,cuts and dent,which surface relief. Element, irregularity or group elements and irregularities of the real surface, unintentionally or accidentally b1051 during manufacture, storage, handling or use of the surface.