DIN 41494 PDF

Buy DIN () Mechanical Structures For Electronic Equipment; Mechanical Structures Of The ,6 Mm (19 Inch) Series; Components On Front . DIN Mechanical structures for electronic equipment; mechanical structures of the ,6 mm (19″)series; components on front panels; mounting. Category:DIN Good pictures. Advanced All images; Featured pictures; Quality images; Valued images; In this category and in In this.

Author: Meziktilar Yozshujinn
Country: Slovenia
Language: English (Spanish)
Genre: Travel
Published (Last): 11 October 2006
Pages: 111
PDF File Size: 6.64 Mb
ePub File Size: 8.77 Mb
ISBN: 296-5-81951-878-4
Downloads: 57342
Price: Free* [*Free Regsitration Required]
Uploader: Voodoolkree

19-inch rack

Threaded mounting holes in racks where the equipment is frequently changed are problematic because the threads can be damaged or the mounting screws can break off; both problems render the mounting hole unusable.

All Wikipedia articles needing words, phrases or quotes attributed Wikipedia articles needing words, phrases or quotes attributed from November Commons category link is on Wikidata.

Hole spacing is 25 millimetres 0. This page was last edited on 12 Decemberat fin Slides or rails for computers and other data processing equipment such as disk arrays or routers often need to be purchased directly from the equipment manufacturer, as there is no standardization on such equipment’s thickness measurement from the side of the rack to the equipment or means for mounting to the rail.

The term relay rack appeared first in the world of telephony. The vin pattern thus repeats every 1. There is no standard for airflow and cooling of rack mounted equipment. Portable rack cases using a rotary-molded polyethylene outer shell are a lower-cost alternative to the more durable ATA-approved case.

Nineteen-inch racks are also often used to house professional audio and video equipment, including amplifierseffects unitsinterfaces, headphone amplifiers, and even small scale audio mixers.

  JUNG SEMINAR ON NIETZSCHE ZARATHUSTRA PDF

For example, an oscilloscope might be 4U high, and rack-mountable computers are mostly between 1U and 4U high. Open Rack is a mounting system designed by Facebook ‘s Open Compute Project that has the same outside dimensions as typical inch racks e. Occasionally, 414494 may see fractional U devices such as a 1. The First Stored Program Computer.

A inch rack is a standardized frame or enclosure for mounting multiple electronic equipment modules. Racks are divided into regions, End covers are typically secured with either a simple draw latch or a rotary cam “butterfly” latch, named for the 14494 of the twist handle. From Wikipedia, the free encyclopedia. To protect equipment from shock and vibration road rack cases use an inner and outer case.

When rack rails are too thin to tap, rivnuts or other threaded inserts can be used, and when the particular class of equipment to be mounted is known dun advance, some of the holes can be omitted from the mounting rails.

Category:DIN – Wikimedia Commons

Servers and deep pieces of equipment are often mounted using rails that are bolted to the front and rear posts as above, it is common for such rails to have an adjustable depthallowing the equipment to be supported by four posts, while also enabling it to be easily installed and removed. When in place, the equipment may also then be bolted to the rack. Low-wattage devices may not employ active cooling, but use only passive thermal radiation and convection to dissipate heat.

Racks carrying telecom equipment like routers and switches often have extra width to accommodate the many cables on the sides. The height of a rack can vary from a few inches, such as in a broadcast console, to a floor mounted rack whose interior is 45 rack units See also Industrial PC. The inch dimension includes the edges, or “ears”, that protrude on each side which allow the module to be fastened to the rack frame with screws.

  ED LEEDSKALNIN MAGNETIC CURRENT ILLUSTRATED PDF

These cases can be isolated by thick layers of foam or may use spring-loaded shock mounting. Archived from the original on With the prevalence of inch racks in the Telecoms industry, the same practice is also common, but with equipment having inch and inch brackets available, enabling them to be mounted in existing racks.

The size denotes the width of the faceplate for the installed equipment. The rails may also be able to fully support the equipment in a position where it has been slid clear of the rack; this is useful for inspection or maintenance of equipment which will then be slid back into the rack. The 41449 shell is frequently embossed in a self-mating pattern to combat the tendency for stacked cases to deform slightly creating a slope that encourages the upper case to slide off.

inch rack – Wikipedia

Views Read Edit View history. However, not all equipment is suitable for this type of mounting. Tapping large numbers of holes that may never be used 14494 expensive; nonetheless tapped-hole racks are still in use, generally for hardware that rarely changes.

The extra width and depth cin cabling to be routed with ease also helping to maintain bend-radius for fibre and copper cables and deeper equipment to be utilised. Patent 2,granted Oct.