Préampli-Processeur CHORD DSP R VENDU TRÈS RARE! Préampli processeur exceptionnel en HC et, fait beaucoup plus rare. Chord dsp r preamp / surround controller, boxed. CHORD DSP R preamp/ surround controller. with dts and dolby 2 surround. Introduction The Chord DSP forms the centre of a High -End cinema and audio system. The DSP decodes Dolby Digital, DTS and DTS-ES and has the.
|Published (Last):||20 August 2009|
|PDF File Size:||3.38 Mb|
|ePub File Size:||17.2 Mb|
|Price:||Free* [*Free Regsitration Required]|
Each speaker can be set to be between 0 feet 0. Use the up and down LCD touch pads or front panel buttons to change the scale of the meter.
The Autocalibration facility makes things even easier as it automatically calculates the correct speaker distances and level settings. This is so that you hear the full surround image as intended regardless of your speaker configuration.
Whilst in the set -up menus, if you have made changes chotd wish to keep then press this button to save and exit. Pressing this button will also un -mute the outputs if they are muted to prevent a sudden increase in volume from causing any damage to you loudspeakers or your ears. Make sure that you connect the correct colour cohrd to each other. Size setup Used to define which speakers are present and whether they can handle low frequencies.
It can be used to provide a video signal to an additional display device. This can happen due to video processing – in projectors, plasma screens and standalone video processors. This takes a few minutes to complete. There are several actions that you can choose to cause the trigger. The table below shows the available modes for the dsp80000r input signals and the active output channels associated with each mode.
Blue goes to blue, green goes green and ds;8000r goes to red. For example you may wish to use this connection to feed a display device located in another room. Treble This setting allows you to adjust the treble or high frequency content of the main audio output. This is to ensure that there will always be an audio signal present at the record outputs when using an analogue tape recorder. To increase the volume or increase parameter settings in the user interface menus, turn the volume knob clockwise.
If this button is pressed whilst not in the menus then the button functions as an active input source search touch pad.
It is recommended that where possible, balanced connections with XLR connectors should be used instead of unbalanced RCA connections.
Use the left and right cursor LCD touch pads or front panel buttons to adjust the gain setting so that the signal never clips.
Determine if a balanced audio input signal is used? Circuit designs that embody these components conform to applicable safety requirements.
We hope you have many hours of enjoyment from this product. Hcord function is called Late Night as it is useful to use late at night when you do not wish to listen to loud and dynamic soundtracks.
吏?? ?濡 GLV – Create arts through technology!
Each time the button is pressed the selected input source will be decremented by one. Trigger 1 duration Duration determines the amount of time chor trigger voltage is output for when activated. S-Video or Component Video connections are preferred as they offer better quality video signals than Composite Video. You can use these inputs to connect in a number of configurations including mono, stereo, 5. Auto mode will automatically select the best video source present.
DSP 8000 AV Processor
Video format This setting determines which type of video input you are using. If the measurement is too long i.
The main menu cyord the first menu that is encountered after pressing either of these buttons. The setting will be overridden if you use a Preset setting for an input. Chord guarantee registration card 5 when setting up To ensure that your Chord processor works efficiently and safely, please pay particular attention to the following issues.
Preset Set-up Configures up to five user preset settings.
DSP AV Processor |
This equalisation can be used to compensate for the added brightness without affecting the quality of the treble range. Press this LCD touch pad to increase the value of a selected parameter within the set up menu. Three component video inputs and one output support HDTV-formats. This should be used at all times. The remote control main menu screen is shown in the diagram below. This input also allows another bypass route for use with sources that need to avoid the digital processing boards in the DSP This is done to keep the highest quality signal for component replay.
For example if you are connecting a DVD player, make sure that the audio and video connections have the same number. Manufactured under license from Digital Theatre Systems, Inc.
The subwoofer crossover frequency can be set from 40 Hz to Hz in steps of 10 Hz.
Turn the microphone ON. Exit On Screen Display Level setup Allows you to adjust the relative levels from each of your speakers.