CEI EN 50160 PDF

EN Caratteristiche della tensione fornita dalle reti pubbliche di distribuzione utilizzare un registratore conforme alla CEI EN In questo. Power quality has many meanings depending on what the power is used for. • Measuring PQ is all about deviations from normal state. • USERS. of European Norm Some countries have used EN as the basis for their national quality of supply regulations. But the standard’s statistical models.

Author: Shakazahn Galkis
Country: Croatia
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 2 December 2005
Pages: 258
PDF File Size: 12.40 Mb
ePub File Size: 15.96 Mb
ISBN: 710-9-87601-502-1
Downloads: 94749
Price: Free* [*Free Regsitration Required]
Uploader: JoJogis

For the algorithm validation a reference network has been used and the causes of voltage sags have been later implemented on it. The Power quality measurement methods, Ed.

Then signal S occurs: The problem arises when it is necessary to apply such a general definition to a particular product such as electricity. The purpose of the project is to create a network that can monitor systematically the power quality of a site.

The project is related to the development of a sensors’ network to measure Power Quality with the ability to connect it both wirelessly and 501160 wiringfor the analysis of a low-voltage grid. The signal source is the power quality calibrator Fluke A, a programmable source of stable voltage and ne waves, distorted by harmonics, flicker, interharmonics and other phenomena fig.

This change should be assessed by comparing the value of reactive power in the system, i. Another aspect, which should not be neglected, is the resonance issue related to the presence of harmonics in electrical networks.

  DELO AUTOMIX 1895 PDF

This is important for a een use in all situations that require a detailed analysis of the electrical system from the point of view of the characterization of PQ, without the adoption of expensive specialized tools. Due to their characteristics, the input signal is faithfully reproduced, also ensuring excellent insulation from the network.

The calculation of 50106 phase follows the same logic of the frequency detector of the PLL VCO where the samples were replaced by the current samples measured: Another direction ccei with getting new waveform amplitude in steady state regime. Finally a parity byte is sent. The sags may affect one or more stages depending on the phenomena that cause them.

Finally, we are working on a new version of the sensor’s prototype that will significantly reduce its size, consumption and costs.

The starting method is the study of the flow of reactive power [9]. One of the objectives pursued in the design was to obtain the flexibility of the module, in order to be used for different measurements. When the sag event occurs Q t’ is calculated.

Metrel d.d. – Power Quality Analysis

The algorithm discussed above is implemented within the sensors network in order to obtain a distributed measurement system to detect the directionality of sags. Some processes are profoundly affected even by very short breaks, for example:.

Even if this prototype is powered by the network you are trying to 501660 consumption considerably by working on the sensors, in order to be independent from the network supply.

As you can see the first node F brings the values of the network at the point of measurement, and the variables related to the load from which it is 501660 to obtain a complete characterization: This single device realizes the SPQ block of the network shown in Fig.

  EPAP MODELLO 2 2012 PDF

New products

The following are the most interesting values Table 2. Tecniche di prova e di misura – Metodi di misura della qualita della potenza. The Table VII presents the results of calibration: The acceptability of the deviations from the nominal characteristics of the energy depends on the type of use by the user, the equipment installed and its needs.

For the acquisition of voltage and current signals, we used two Hall effect sensors. The router is a device consisting only of much smaller processor that manages the ZigBee protocol and the RF card.

The reference network is a schematic of a singlephase low voltage network. The simulations were divided into two parts: It is possible, by changing a few lines of code, to implement functions that return a set of parameters than those currently produced. Similarly, the failure was simulated upstream of the monitoring point. In this case, in addition to stability, a high immunity to all line disturbances is required, disturbances which presumably will be the ones that the sensor must detect and analyze.

Harmonic issues have fei investigated more deeply.