CatEye CC-MT [Mity 2] • User guide • Download PDF for free and without registration!. Following pdf manuals are available: cat-eye cc-mt mity 2 User Manual. CatEye product manuals for the entire line of CatEye cycle computers, headlights , safety lights and accessories online support at

Author: Akinom Dilkree
Country: Czech Republic
Language: English (Spanish)
Genre: Automotive
Published (Last): 4 October 2005
Pages: 65
PDF File Size: 9.17 Mb
ePub File Size: 12.62 Mb
ISBN: 944-5-34777-216-8
Downloads: 43009
Price: Free* [*Free Regsitration Required]
Uploader: Kazraktilar

Moves between wheel circumference and. Moves dateye the next function. How the display changes. In TmAv and Dst 1, 2 display. Completes setting Ready for measuring. Moves between wheel circumference A and B. Increases the figure by one. Rapidly increases the figure.

Decreases the figure by one. Rapidly decreases the figure. Moves from hour digits to minute digits.

Press all the three buttons simultaneously. In Wheel Circumference Setting Display: If SET button is pressed in Odo display stop statewheel circumference manuzl display appears. In Clock Time Setting Display: If SET button is pressed in. When measuring, the speed scale flashes. Keep your eyes on. Periodically check if the.

Do not place it within mitj reach. Never disassemble the main unit. Softly wash away such objects with water. Average Pace Arrow D. Auto Mode Symbol F. Wheel Selection Symbol G.

All displays illuminate, and then ” K ” symbol flashes. Input wheel circumference A. For inputting wheel circumference B, hold down SET button. Input the figure in the same way. Press S or SET button to fix it. Press SET button to fix it. Input the figure by MODE button.

Operating instructions | CatEye CC-MT [Mity 2] User Manual | Page 2 / 2 | Original mode

Press S button to change the flickering digit. Refer to the “Installation Manual”. Using this unit for the first time. Usually displayed on the upper display and updated once a second. When Av or Mx data is shifted to the upper display, Spd shifts to the lower display. Shows whether the current speed is faster or slower than the average speed.

CatEye CC-MT [Mity 3] User Manual | 4 pages | Original mode | Also for: CC-ED, CC-VL

When the average speed is zero, or when in the stop state, no pacer symbol appears. Continuously measured until battery wears down. With all clear operation, it cxteye to zero; to continue accumulation of data, input the previous Catyee data after all clear operation.


Trip Distance 1, 2. The trip distance from start to current point is displayed. Two different start points can be set Dst1 and Dst2. Dst2 is best for measuring a sec- tional distance.

With Reset ,ity, it returns to zero. Reset of Dst2 is done independently of the other reset and does not affect the other data. Elapsed time is measured from start to current point, in units of hours, minutes and seconds.

At 10 hours, it returns to zero and counting begins anew. With the press of S button, Tm data shifts to the upper display. In this case, the lower display shows the hour digits of Tm data instead of Spd. The average speed from start to current point is displayed. If the elapsed time exceeds 27 hours or Dst1 exceeds E is displayed and calculation ceases.

With the press of S button, Av data shifts to the upper display. In this case, Spd data is shifted to the lower display. With reset operation, it returns to zero. Displays the highest recorded speed.

With the press of S button, Mx data shifts to the upper display. If “M” is selected for speed scale, the clock time is in 12 hour. If “K”, the clock time is 24 hour. When the main unit does not receive a signal, or a button has not been pressed for minutes, the power supply is shut down and the main unit will only display the clock. When the main caeye or the contact gets wet, dry it off with mify cloth; rust will cause functional errors.

Has the battery in the main unit worn out? Replace it with a new one.

Operating instructions – CatEye CC-MT200 [Mity 2] User Manual

Incorrect ccateye appears or the catwye is frozen. Do “All Clear” operation. If possible, write down the Odo data before all clear opera- tion, and input it again after the cateue returns normal. Current speed does not appear. When current speed does not appear, first short-circuit the contact on the back with metal; if the speed display appears, the main unit is normal and the problem must be in the bracket or the sensor.


Is there anything on the contact of the main unit or of the bracket? Wipe the contact clean. DO NOT use abrasives, sandpaper, etc. Is the distance between the sensor and the magnet too far? Are the marking line of the sensor and the center of magnet aligned? Adjust the position of the sensor and magnet again. Is the wire broken? How to Replace Battery. In order to continue accumulation of Odo data, write down the stored Odo before replacing the battery. Continuing Accumulation of Odo Data.

Although the Odo data returns to zero by all clear operation, you can continue accumulation of data by inputting the previous Odo data. Be sure to write down the data before replacing the battery.

The life of the first factory-loaded battery may be shorter than this period. Wheel circumference setting is the actual distance in centimeters on the ground of one wheel revolution measures. For the most accurate settings, do this roll-out. Otherwise, consult the Cross Reference Table for approximate setting.

Tm moves up as Main Display. Av moves up as Main Display. Mx moves up as Main Display. Hold down 2 sec. Data to be reset: In Tm, Av, Mx, Dst1 and.

Best for MTB riding and low speed sensitivity. If these buttons are further held down for more than 3 seconds, the wheel cwteye moves between A or B. Main unit preparation, Button operation reset operation. If SET button is pressed in stop stateclock time setting dis- play appears. Keep your eyes on the road and pay attention to traffic conditions. Periodically check if the screws and secure bands have loosened. If swallowed by mistake, consult a doctor immediately.